# DJI M350

## Installation Instructions

<table data-full-width="false"><thead><tr><th width="89">STEP</th><th width="326">ACTION</th><th>IMAGE</th></tr></thead><tbody><tr><td>1</td><td>Using the included gaff tape, tape over the infrared sensor.<br><br><em>The LiDAR sensor on Gobi slightly occludes the infrared sensor. DJI M350 will throw a sensor avionics error if this is not covered, and there is no software disabling allowed.</em><br><br><em>Please be careful as this sensor is responsible for soft landing. Pilots should land the aircraft manually.</em></td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FmMWatIOh36YvtnrQCqbp%2Fimage.png?alt=media&#x26;token=abe045ab-3e79-4201-a9a5-c613717ccb77" alt="" data-size="original"></td></tr><tr><td>2</td><td>Locate the four screw holes for installing the payload mount.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FmMWatIOh36YvtnrQCqbp%2Fimage.png?alt=media&#x26;token=abe045ab-3e79-4201-a9a5-c613717ccb77" alt="" data-size="original"></td></tr><tr><td>3</td><td>Using the M3x10 screws, install the payload mount.<br><br>Payload insertion point should be aligned with the front of the aircraft.<br></td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FrXzgV505uh9eKSYKeHQy%2FA7300032.JPG?alt=media&#x26;token=c7f0cda4-55f3-4a30-a585-86b3695eba8c" alt="" data-size="original"></td></tr><tr><td>4</td><td>Place the power delivery module on top of the aircraft.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FmiWMSHWG9y6OE3pqm4mP%2FA7300038.JPG?alt=media&#x26;token=258838df-58df-4743-a1da-392ade4214c6" alt="" data-size="original"></td></tr><tr><td>5</td><td>Locate the four screw holes for the power delivery module.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FWMshuuek6zL4RShLddt3%2Fimage.png?alt=media&#x26;token=51829f35-5cfa-4dcf-b1ba-fd5ef711c086" alt="" data-size="original"></td></tr><tr><td>6</td><td>Using the M3x6 screws, install the power delivery module. <br><br>USB-C port should be facing the rear of the aircraft, power cable should come off the right side of the aircraft when looking from the back.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FMRSGncfowfiZh13lexNw%2FA7300043.JPG?alt=media&#x26;token=c5efce97-3914-4229-91b8-fcbc512ac4ff" alt="" data-size="original"></td></tr><tr><td>7</td><td>Attach the power delivery cable from the module to the aircraft.<br><br>Follow the attached DJI documentation. <br><br>The B side of the power module side should face up.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FnwqvEaQtx93m9u2J2eUF%2FA7300056.JPG?alt=media&#x26;token=ad98ad2d-8268-46d1-ba21-ccac470e9612" alt="" data-size="original"></td></tr><tr><td>8</td><td>The B side of the aircraft side should face out.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FydArSiudDEXQou8v14r5%2FA7300057.JPG?alt=media&#x26;token=eb31820e-b6a8-4f46-93d4-fc0fb2efe070" alt="" data-size="original"></td></tr><tr><td>9</td><td>Install the antenna mounts.<br><br>Locate and line up the notches on the antenna mount and C-bracket when installing.<br></td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2F3Pmm4sG5OvZn6UJME5k7%2FA7300046.JPG?alt=media&#x26;token=1169a0e3-b776-4142-a295-2ff9d93eacbe" alt="" data-size="original"></td></tr><tr><td>10</td><td>Antenna mount should sit flush against the end of the rotor arm.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2F3d45BYq3WAJgEC3ChNhv%2FA7300048.JPG?alt=media&#x26;token=d2048b3a-493c-4035-a1ef-86f3d8e1f0c3" alt="" data-size="original"></td></tr><tr><td>11</td><td>Antenna A1 should be installed on the rear left of the aircraft.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FkrPfBQ3RAxg0hdS7NmuQ%2FA7300053.JPG?alt=media&#x26;token=711a1ee1-b88d-46a3-a9fd-999635d0a1dc" alt="" data-size="original"></td></tr><tr><td>12</td><td>Antenna A2 should be installed on the rear right of the aircraft.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FoYNgJlbzOHEuESYELF5I%2FA7300051.JPG?alt=media&#x26;token=96e8dfda-06dd-4cfe-9266-db58ae9a4fb8" alt="" data-size="original"></td></tr><tr><td>13</td><td>Ensure the antenna mounts are level with the ground.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FW7VEtPwNBmxq5FTDda53%2FA7300047.JPG?alt=media&#x26;token=0a471e03-f9f2-4f8f-9124-79ba34656678" alt="" data-size="original"></td></tr><tr><td>14</td><td>Loosely zip tie the antenna cables to the back of the payload mount.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2F6aSxEzTOzINKIc7aXoGP%2FA7300058.JPG?alt=media&#x26;token=5a0ea53c-730c-4e8a-bc0f-9529ff13f91f" alt="" data-size="original"></td></tr><tr><td>15</td><td>Make sure the rotor arms can properly fold.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FoJfVHruqNELdnTRLOMW3%2FA7300059.JPG?alt=media&#x26;token=d3be0eb6-dcc4-485c-90fa-53b8fa7b8086" alt="" data-size="original"></td></tr><tr><td>16</td><td>Fully secure the zip ties.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FLusMZ53fMpRBMvZWd7m6%2FA7300060.JPG?alt=media&#x26;token=0abd6744-d61a-48c1-afab-d8dc2b6432c9" alt="" data-size="original"></td></tr><tr><td>17</td><td>Using the included gaff tape, secure the GNSS antenna cable on both sides of the aircraft so the propellers cannot reach them.<br><br>Also ensure the rotor arm locking system is able to extend far enough that the rotor arms can still be closed.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FNASGAcHZsmk2kUp7bLTX%2FA7300061.JPG?alt=media&#x26;token=0bf5e205-9f96-4da3-8660-09f07b163fed" alt="" data-size="original"></td></tr><tr><td>18</td><td>Zip tie the gaff tape/cable to the rotor arm for further security.</td><td><img src="https://1859480457-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F0x7fEbqbQH6LOaUlQlgY%2Fuploads%2FMCxdkpA7XvZ2hWo6f9Q1%2FA7300062.JPG?alt=media&#x26;token=e447d0ad-8870-4f35-8848-30f54e5fddb2" alt="" data-size="original"></td></tr></tbody></table>

Additional information for conducting operations with GOBI and DJI M350 can be found below:

{% content-ref url="<https://app.gitbook.com/s/q2hGbYGESpVDi0Hbli0q/uas-quick-start/dji-m350-rtk>" %}
[DJI M350 RTK](https://app.gitbook.com/s/q2hGbYGESpVDi0Hbli0q/uas-quick-start/dji-m350-rtk)
{% endcontent-ref %}
